Search results

NIce job,not bad for the first ones. Only criticism when you drill the holes for the handle try to center them a little better.The very first thing that my eye went to was that one hole was hi in the handle and the other was low,they didn't line up. Just keep it going and you will get there

Both knives are SOLD,Thanks to all for the nice comments they are greatly appreciated.

It is on it's way, Thanks DAVE

Thanks again,The nice comments are really appreciated

Thanks guys your comments are greatly appreciated.

Just finished these today,both are 154cm@RC61/62,Flat ground,Mirror finish,Checkering on spine,and Pistachio wood handles with black liners The first one is my Sun Bear Trout and Bird (SOLD) Blade length 2 1/2" tip to plunge, Overall Length: 6 1/8" Sheath: Horizontal #2 is my...

Like this? You can probably buy one cheaper than haveing a maker make onre for you.They take a lot of steel.You need a piece 3/32"X5" X6" to make one.I have made four of them including this one I made 35 years ago.Good Luck Thanks to all for the comments

I have sold quite a few of them in Texas to Guides that I have hunted with.I have also included the Skeleton knife with a full size Hunter in the same sheath as well as putting one on the cover of a Hatchet. As I said some like them some don't. Thanks again

Thanks Guys, Some people like Skeleton knives and some don't,So far here I have gotten positive feed back but on another forum all negetive and on another no comments at all. Thanks again

Just finished this one for a customer Model:Skeleton Guthook Steel:1/8' 154CM@RC61/62 Blade"2 1/2" cutting edge,Flat Ground, Mirroer finish Handle: Aluminum Oxide Blasted,Checkering top and bottom Overall length: 7 3/8" Weight: Knife 2oz,Knife and Sheath 6oz Sheath: Back Pocket Design,9oz...

Thanks guys for all the nive words they are greatly appreciated.

Hi Guys and Gals,this is my Personal Drop Point Model,This Knife is AVAILABLE on my web site Steel:440C@RC60/61 Blade:3 3/8" tip to guard,Hollow Ground(very rare for me)Mirror finish Overall Length:8 1/8" Guard:416SS Handle: White Paper Micarta with 2 Black Lines(Old Stock fro the 80s)...

Thanks Guys for the comments they are greatly appreciated

Just finished this one for a good customer. Iwould have liked to uase some spacers for contrast but he dead set against it.You will also notice that my makers mark is barely visiable. Steel: 3/16" Chad Nichols Damascus Blade: length 8" width 1 1/2" Flat Ground with Clip handsanded to 400grt...

Thanks guys for the nice comments, they are greatly appreciated

Hi all, Just finished these today.Still need to Make Sheaths,These Knives are available The first knife came about as I keep all my scrap steel in a drawer and use it to make parts for things and some tools,I also use it to practice file work on. Well I was looking thru my scrap 154 and found...

Thanks Guys, I wish all of you a very Happy New Year and I hope that next year is the best one you have ever had.

This is the last completed knife for 2010. It is for a repeat customer that has one of my Kodiak Guthooks with the same Handle Material. Model:Sun Bear Trout and Bird Steel: 3/32" 154cm Blade: length 2 3/8" tip to plunge,flat ground,mirror finish,checkering on the spine Overall Length:6 1/4"...

3/32 pins in the bolsters and Celuloid. Epoxy on handle is Devcon 2 ton If you were refering to the stripes the celluloid is made that way.It is old stock from the late 80s.I have enough for about 6 more knives and then it's probably all gone.

Thanks guys Merry Christmas to all the mutts out there. I hope the next year is very prosperous for all the tail waggers